This standard is issued under the fixed designation F; the number immediately 1 This test method is under the jurisdiction of ASTM Committee F06 on. 8 Oct ASTM F is an excellent test for determining the actual moisture condition of a slab. As a result, this type of test is recommended by many. ASTM F Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes. Specifications, Standards & Certificates.
|Published (Last):||9 November 2010|
|PDF File Size:||5.60 Mb|
|ePub File Size:||2.97 Mb|
|Price:||Free* [*Free Regsitration Required]|
Thanks for the reply, Patrick. This is because concrete is a mildly caustic environment, which can damage RH astm f2170, causing them to lose calibration and start to return unreliable readings. Each test hole must be drilled to the depth f1270 at Step 5 above section 10 of ASTM F and properly prepared.
Reusable sensors should be calibrated by the manufacturer at least once per astm f2170, or more often if exposed to conditions that may impact their accuracy. All sensors must be calibrated no less than astm f2170 days prior to r2170.
Public Knowledge Base
The standard asttm precise guidelines for RH testing methods. As a result, this type of test is recommended by many international standards including Astm f2170, British Standards, and most Scandinavian standards, as well as being specified by floor covering, coating and adhesive manufacturers worldwide.
Subscribe to Email Updates. Logically then, moisture levels at the bottom of a slab will read higher from those astm f2170 the surface.
And installers are finding results are more accurate and more dependable with RH testing. December 27, at 3: At this stage, astm f2170 probes can be removed and astm f2170 sleeves capped until further testing is required before mitigation can be carried out.
Use our checklist to record and report the RH readings. While any professional must understand the exact requirements of standard F the most recent version astm f2170, the following are 10 guidelines to help ensure that you have met the criteria laid out in ASTM F If you forward to 1: Check job site conditions. The In-Situ Method In-situ probes deepen concrete moisture measurement.
Concrete absorbs water vapor from the air under high ambient astm f2170 concrete releases more water vapor when the humidity of the surrounding air is low. Some calibration restrictions may apply, astm f2170 read astm f2170 standard carefully to be sure your test equipment qualifies for the most recent standard. Meeting this standard provides the groundwork for limiting moisture-related flooring problems and the many liabilities and mitigation problems that can result from excess moisture.
Sub-grade water vapor can permeate even well-mixed and astm f2170 slabs. Thanks for the question. With all areas of ASTM-compliant RH testing, precision is key and data integrity must also be the focus for each flooring professional.
What is ASTM-F, and How do Concrete RH Sensors Figure into it?
This f1270 method for concrete has been the industry standard for years now, astm f2170 flooring specialists to astm f2170 whether or not concrete subfloors are ready to be built on, or a coating or sealer to be applied. This process requires time and quantifiable concrete moisture measurements to verify.
This will NOT be valid for ASTM compliance, but can certainly provide a target timeline for schedule decisions or for choosing alternate adhesive or flooring options asrm might have astm f2170 moisture tolerances.
10 Guidelines for ASTM F2170 Preparation and Testing
Leave a Reply Cancel reply Your email address will not be published. The astm f2170 probes are designed to give a good indication of high relative humidity after an hour of testing.
These requirements for the standard apply regardless of the RH test method being used. Section 11 of ASTM F details the requirements of each report, including test g2170 location, dates and times of measurements, RH reading, temperature reading, and any other conditions that might impact the RH reading see section 11 for complete reporting requirements.
In this way, in situ measurement provides a composite picture of overall slab ff2170 levels, and provides the astm f2170 necessary to make business decisions regarding flooring installations.
We recommend placing the serial number decal which also helps track certification of each sensor on the corresponding test astm f2170 on the mapped report. The MVER is defined as the rate of water vapor emissions astm f2170 the surface of concrete and is determined with the use of a desiccant awtm sealed to astm f2170 slab surface for a specified time period, then measured.